压扁检测标准

原创来源:北检院    发布时间:2023-02-08 14:46:32    点击数:

全国服务领域:河北、山西、黑龙江、吉林、辽宁、江苏、浙江、安徽、福建、江西、山东、河南、湖北、湖南、广东、海南、四川、贵州、云南、陕西、甘肃、青海、台湾、内蒙古、广西、西藏、宁夏、新疆、北京、天津、上海、重庆、香港、澳门

压扁检测标准相关信息

GB/T 39249-2020 橡胶和塑料软管及非增强软管 织物增强型 低温压扁试验
简介:
信息:ICS:23.040.70 CCS:G42 发布:2020-11-19 00:00:00.0 实施:2021-10-01 00:00:00.0

ISO 8492:2013 金属材料——管——压扁试验
简介:
信息:ICS:77.040.10 CCS发布:2013-11-05 实施

KS B ISO 8492-2001(2016) 金属材料 - 管 - 压扁试验
简介:
信息:ICS:77.040 CCS发布:2001-12-31 实施

GB/T 39249-2020 橡胶和塑料软管及非增强软管 织物增强型 低温压扁试验
简介:
信息:ICS:23.040.70 CCS:G42 发布:2020-11-19 00:00:00.0 实施:2021-10-01 00:00:00.0

EN ISO 8492-2013 金属材料.管材.压扁试验
简介:Diese Internationale Norm legt ein Verfahren zur Bestimmung der Eignung metallischer Rohre mit kreisformigem Querschnitt fest, einer plastischen Verformung durch Falten unterzogen zu werden. Das Verfahren darf auch zur Sichtbarmachung von Fehlern in den Rohren angewendet werden. Diese Internationale Norm gilt fur Rohre mit einem Ausendurchmesser von hochstens 600 mm und einer Wanddicke von hochstens 15 % des Ausendurchmessers. Der Bereich des Ausendurchmessers oder der Wanddicke, fur den diese Internationale Norm gilt, kann genauer in der zutreffenden Produktnorm festgelegt sein.
信息:ICS:77.040.10 CCS:H22 发布:2013 实施:2013-11

KS B ISO 8492-2001(2021) 金属材料管子压扁试验
简介:
信息:ICS:77.040 CCS发布:2001-12-31 实施

GB/T 246-2017 金属材料 管 压扁试验方法
简介:
信息:ICS:77.040.10 CCS:H23 发布:2017-07-12 00:00:00.0 实施:2018-04-01 00:00:00.0

PPI TR-47-2011 盘绕式HDPE管的管刚度试验和压扁试验.及在管道应用中与埋藏深度的关系
简介:
信息:ICSCCS发布:2011-05-01 实施

ASTM E1652-2000 金属屏蔽的铂电阻温度表、基金属热电耦和贵金属热电偶制造中使用的氧化镁,铝氧化粉和压扁绝缘物的标准规范
简介:1.1 This specification covers the requirements for magnesium oxide (MgO) and aluminum oxide (Al2O3) powders and crushable insulators used to manufacture metal-sheathed cables of platinum resistance thermometers (PRTs) and noble metal thermocouples. 1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息:ICS:17.200.20 (Temperature-measuring instruments); 29. CCS:N11 发布:2000 实施

GB/T 21899-2008 割草压扁机
简介: 本标准规定了割草压扁机的型式及型号、基本参数、技术要求、试验方法、检验规则、标志、包装、运输和贮存。 本标准适用于往复式割草压扁机和旋转式割草压扁机。
信息:ICS:65.060.50 CCS:B91 发布:2008-06-03 实施:2009-01-01

ASTM B968/B968M-2010 铜及铜合金管和管道压扁试验的标准试验方法
简介:When properly performed and interpreted, the flattening test will provide information about the relative ductility of a tube and presence of surface defects. For welded tube products, the test will provide information on the integrity of the weld seam. In certain product specifications which establish requirements for tubes of sizes greater than 4 in. [100 mm], the test may be allowed as a substitute to the expansion pin test in B153.1.1 This test method establishes the requirements for the flattening test for copper and copper alloy pipe and tube of all sizes. The method addresses both inch-pound and metric considerations, and both seamless and welded product. 1.2 Units8212;Values stated in either inch-pound units or SI units are to be regarded as standard. Within the text, SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息:ICS:77.150.30 (Copper products) CCS:H62 发布:2010 实施

JB/T 9699-1999 割草压扁机.试验方法
简介: 本标准规定了割草压扁机的田间试验方法。 本标准适用于割草压扁机的田间试验。
信息:ICSCCS:B91 发布:1999-08-06 实施:2000-01-01

GB/T 246-2007 金属管.压扁试验方法
简介:本标准规定了测定圆形横截面金属管塑性变形能力的压扁试验方法,包括显示其缺陷。本标准适用于外径不超过600 mm,壁厚不超过外径的15%的金属管。本标准适用的金属管外径和壁厚范围可以在相关的产品标准中做更详细的规定。
信息:ICS:77.040.10 CCS:H23 发布:2007-07-18 实施:2008-02-01

ASTM E1652-2010 金属包覆铂阻温度计、贱金属热电偶和贵金属热电偶制造用氧化镁和氧化铝粉末以及可压扁绝缘体标准规范
简介:1.1 This specification covers the requirements for magnesium oxide (MgO) and aluminum oxide (Al2O3) powders and crushable insulators used to manufacture metal-sheathed platinum resistance thermometers (PRTs), noble metal thermocouples, base metal thermocouples, and their respective cables. 1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息:ICS:29.035.30 CCS:N11 发布:2010 实施

ASD-STAN PREN 3745-513-1999 航空航天系列.航空器用光纤和光缆的试验方法.第513部分:抗压扁性;第P1版
简介:
信息:ICSCCS发布:1999-05-31 实施

GB/T 246-1997 金属管 压扁试验方法
简介: 本标准规定了金属管压扁试验方法的原理、符号、试样、试验设备、试验程序、试验结果评定和试验报告。 本标准适用于外径不超过400mm,管壁厚度不超过外径15%的圆形横截面无缝和焊接金属管压扁塑性变形能力的测定。
信息:ICS:77.040.10 CCS:H23 发布:1997-11-11 实施:1998-05-01

KS M ISO 11093-9-2008 纸和纸板.硬纸板锥形圆筒的检验.第9部分:抗压扁性的测定
简介:이 규격은 감겨진 종이 및 판지 지관의 최대 평면 압축 강도를 측정하는 방법에 대하여 규정
信息:ICS:85.060 CCS:Y30 发布:2008-04-02 实施:2008-04-02

ISO 8492-1998 金属管 压扁试验方法
简介:本标准规定了测定圆形横截面金属管塑性变形能力的压扁试验方法,包括显示其缺陷。 本标准适用于外径不超过600 mm,壁厚不超过外径的15 9/6的金属管。本标准适用的金属管外径和壁厚范围可以在相关的产品标准中做更详细的规定。
信息:ICS:77.040.10 CCS:H23 发布:1998-11 实施

GB/T 13440-1992 无缝气瓶压扁试验方法
简介: 本标准适用于检验无缝气瓶的多轴向应变能力,规定了无缝气瓶压扁变形能力的测定方法。 本标准适用于公称工作压力不大于30MPa,公称容积不大于80L的无缝气瓶(简称气瓶)。
信息:ICS:23.020.30 CCS:J76 发布:1992-04-08 实施:1992-12-01

KS M ISO 11093-9-2008 纸和纸板.硬纸板锥形圆筒的检验.第9部分:抗压扁性的测定
简介:이 규격은 감겨진 종이 및 판지 지관의 최대 평면 압축 강도를 측정하는 방법에 대하여 규정
信息:ICS:85.060 CCS:Y30 发布:2008-04-02 实施:2008-04-02

ISO 8492:1998 金属材料.管子.压扁试验
简介:
信息:ICS:77.040.10 CCS发布:1998-10-22 实施

GB/T 2653-1989 焊接接头弯曲及压扁试验方法
简介: 本标准规定了金属材料焊接接头的横向正弯及背弯试验、横向侧弯试验、纵向正弯及背弯试验、管材压扁试验方法,以检验接头拉伸面上的塑性及显示缺陷。 本标准适用于熔焊和压焊对接接头。
信息:ICS:25.160.40 CCS:J33 发布:1989-05-08 实施:1990-01-01

TCVN 1830-2008 金属材料.管材.压扁试验
简介:
信息:ICSCCS发布:2008 实施

AECMA PREN 2002-10-1998 航空航天系列.金属材料 试验方法.第10部分:管子压扁试验.P2版
简介:This draft is now available for public comment and your views and technical comments on it would be appreciated. If you have no specific comments to make hut find it generally acceptable it would be helpful if you would notify US accordingly. Suggestions entailing revision of the text should indicate the preferred wording. Please quote the relevant clause number against any comment.
信息:ICS:49.060 CCS:V11 发布:1998 实施

ASTM B968/B968M-16(2022) 铜及铜合金管压扁的标准试验方法
简介:
信息:ICS:77.150.30 CCS发布:2022-05-01 实施

ASD-STAN PREN 3475-515-2008 航空航天系列.航空器用电缆的试验方法.第515部分:抗压扁性;第P1版
简介:
信息:ICSCCS发布:2008 实施

ASD-STAN PREN 2002-10-1998 航空航天系列.金属材料试验方法.第10部分:管材压扁试验;第P2版
简介:
信息:ICSCCS发布:1998 实施

DB13/T 2730-2018 小型自走式刈割压扁机通用技术要求
简介:
信息:ICS:65.060.20 CCS:B 91 发布:2018-07-16 实施:2018-08-16

BS ISO 11093-9-2006 纸和纸板.芯层试验.抗压扁性的测定
简介:This part of ISO 11093 specifies a method for the determination of the maximum flat crush resistance of wound paper and board cores.
信息:ICS:85.060 CCS:Y31 发布:2006-11-30 实施:2006-11-30

SNI 07-4601-1998 金属材料管压扁试验
简介:
信息:ICS:77.040.10 CCS发布:1998 实施

DB62/T 2676-2016 割草压扁机田间作业技术规范
简介:
信息:ICS:65.060.50 CCS:B 91 发布:2016-07-29 实施:2016-08-31

SANS 8492-2003 金属材料.金属管.压扁试验
简介:Specifies a method for determining the ability of metallic tubes of circular cross-section to undergo plastic deformation by flattening. It may also be used to reveal the defects in the tubes. This International Standard is applicable to tubes having an
信息:ICS:77.040.10 CCS:H22 发布:2003-09-19 实施

NEN-EN 10237-1994 金属管 压扁试验方法
简介:Deze Europese norm specificeert een methode voor een trekproef aan ringen van buizen om oppervlakte- en inwendige fouten bloot te leggen door de proefstaaf aan een spanning te onderwerpen tot breuk plaatsvindt. Deze proef kan ook worden gebruikt om de vervormbaarheid van buizen vastte stellen.De trekproef aan ringen is van toepassing op buizen met een uitwendige middellijn groter dan 150 mm en een wanddikte niet groter dan 40 mm. De inwendige middellijn moet groter zijn dan 100 mm.
信息:ICSCCS发布:1994-05 实施:1994-05

DB34/T 2619-2016 数控茶叶压扁机技术条件
简介:本标准规定了数控茶叶压扁机的术语和定义、技术要求、试验方法、检验规则及标牌、包装、运输和贮存。 本标准适用于批量生产扁形茶叶的数控茶叶压扁机(以下简称压扁机)。
信息:ICS:67.260 CCS:X 99 发布:2016-06-15 实施:2016-07-15

NF E62-519-2003 削扁柱形柄刀具用螺钉压紧刀具夹头(端铣刀夹头).第1部分:刀柄驱动系统尺寸
简介:
信息:ICS:25.060.20 CCS:J52 发布:2003-03-01 实施:2003-03-20

DS/EN 10233-1994 金属材料.导管.压扁试验
简介:This European Standard specifies a method for determining the ability of metallic tubes of circular cross-section to undergo plastic deformation by flattening. It may also be used to show up defects in the tubes.The standard is applicable to tubes having an outside diameter not greater than 600 mm and a thickness not greater than 15 % of the outside diameter. The range of the outside diameter, or thickness, for which this European Standard is applicable could be more exactly specified in the relevant product standard.
信息:ICSCCS发布:1994-04-12 实施:1994-04-12

NY/T 2850-2015 割草压扁机 质量评价技术规范
简介:本标准规定了割草压扁机的基本要求、质量要求、检测方法和检验规则。本标准适用于与拖拉机配套的往复式割草压扁机和旋转式割草压扁机的质量评定。
信息:ICS:65.060.99 CCS:B93 发布:2015-10-09 实施:2015-12-01

NF E62-520-2003 削扁柱形柄刀具用带压紧螺钉刀具夹头(端铣刀夹头).带7/24锥柄的夹头尺寸
简介:
信息:ICS:25.060.20 CCS:J52 发布:2003-03-01 实施:2003-03-20

NF A03-092-1994 金属材料.管材.压扁试验
简介:
信息:ICS:77.040.10 CCS:H23 发布:1994-02-01 实施:1994-02-20

ASTM E1652-2015 基金属热电耦, 金属外壳的铂电阻温度计和贵金属热电偶制造中使用的氧化镁和氧化铝粉末及压扁绝缘子的标准规格
简介: 1.1x00a0;This specification covers the requirements for magnesium oxide (MgO) and aluminum oxide (Al2O3) powders and crushable insulators used to manufacture base metal thermocouples, metal-sheathed platinum resistance thermometers (PRTs), noble metal thermocouples, and their respective cables. 1.2x00a0;The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.3x00a0;This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息:ICS:17.200.20 CCS发布:2015 实施

ASTM E1652-2003 金属外壳的铂电阻温度表、基金属热电耦和贵金属温差热电偶制造中使用的氧化镁和氧化铝粉末及压扁绝缘子的标准规范
简介:1.1 This specification covers the requirements for magnesium oxide (MgO) and aluminum oxide (Al2O3) powders and crushable insulators used to manufacture metal-sheathed platinum resistance thermometers (PRTs), noble metal thermocouples, base metal thermocouples, and their respective cables.1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息:ICS:17.200.20 (Temperature-measuring instruments); 29. CCS:N11 发布:2003 实施

ONORM EN 10233-1994 金属材料.管.压扁试验
简介:In dieser Europ?ischen Norm ist ein Verfahren zur Bestimmung des Faltverhaltens von Metall r?hren mit kreisf?rmigem Querschnitt festgelegt. Diese Prüfung darf auch zur Sichtbarmachung von Fehlern in Rohren angewendet werden.Die Norm Ist anwendbar auf Rohre mit einem Au?endurchmesser nicht gr??er als 600 mm und einer Wanddicke nicht gr??er als 15 X des Au?endurchmessers.Der Bereich des Au?endurchmessers oder der Wanddicke, für den diese Europ?ische Norm zutrifft, kann genauer in der entsprechenden Erzeugnisnorm festgelegt sein.
信息:ICSCCS发布:1994-01-01 实施:1994-01-01

NF A03-092-2014 金属材料.管材.压扁试验
简介:La présente Norme internationale spécifie une méthode de détermination de l'aptitude à la déformation plastique par aplatissement de tubes métalliques de section circulaire. Elle peut également être utilisée pour mettre en évidence les défauts des tubes.
信息:ICS:77.040.10 CCS:H22 发布:2014-07-04 实施:2014-07-04

ISO 5414-1-2002 扁方柄刀具用螺钉压紧刀具夹(立铣刀刀夹).第1部分:刀柄驱动系统的尺寸
简介: 本部分规定了带紧固螺钉的刀具夹头(立铣刀夹头)及其紧固螺钉的尺寸,还给出厂夹头端面的最大直径。这种夹头用于按GB/T 6131.2的削平型直柄刀具的传动。 本部分规定了两种传动型式: —一一孔径d1≤20 mm的夹头,用于传动单削平型直柄刀具。这类刀具既町做成单头的也可做成双 头的。 ——孔径d1≥25 mm的夹头,用于传动双削平型直柄刀具。这类刀具只做成单头的。 注:各型夹头的连接尺‘十和带紧固螺钉的刀具夹头(立铣刀夹头)的标记按GB/T 6133.2的规定。
信息:ICS:25.060.20 CCS:J52 发布:2002-11 实施

NBN-EN 10233-1994 金属管.管道.压扁试验方法
简介:
信息:ICSCCS发布:1994 实施:1994

DB62/T 2456-2014 割草压扁机
简介:
信息:ICS:65.060.20 CCS:B91 发布:2014-04-21 实施:2014-05-01

ISO 5414-2-2002 扁方柄刀具用螺钉压紧刀具夹(立铣刀刀夹).第2部分:夹头的连接尺寸和名称与符号
简介:本部分规定了带紧固螺钉的刀具夹头(立铣刀夹头)的连接部分的尺寸及夹头的标记, 这种夹头用于按GB/T 6131.2 的削平型直柄铣刀的传动。本部分规定了两种连接型式:--按ISO 297 手动换刀和按GB/T 10944.1 自动换刀的带 7 :24 的锥柄夹头, 适用于单削平型或双削平型的手动和自动换刀的刀柄。注:本部分给出的自动换刀的30号 7 :24锥柄刀夹的尺寸是未标准化的。-- GB/T 1443 和 GB/T 4133 莫氏锥柄夹头, 只适用于单削平型的刀柄。注:刀柄传动系统的尺寸按 GB/T 6133.1 的规定。
信息:ICS:25.060.20 CCS:J41 发布:2002-11 实施

STAS ISO 8492-1992 金属材料.管.压扁试验
简介:Prezentul Standard interna?ional, specific? o metod? de determinare a aptitudinii la deformarea plastic? prin aplatizare a ?evilor metalice de sec?iune circular?, cu diametrul exterior de maximum 400 mm ?i cu grosimea peretelui de maximum 15% din diametru
信息:ICSCCS发布:1992 实施:1992

DIN EN ISO 8492-2014 金属材料. 管材. 压扁试验(ISO 8492-2013); 德文版本EN ISO 8492-2013
简介:
信息:ICS:77.040.10 CCS:H48 发布:2014-03 实施

KS W ISO 1966-2002 航空器电缆的压扁接头
简介:1.1 이 규격은 해당 형식의 케이블에 대해 지정된 도선의 안정화된 온도(즉, 105℃,
信息:ICS:49.06 CCS:V40 发布:2002-09-28 实施:2002-09-28

DS/ISO 8492-1989 金属材料.管材.压扁试验
简介:Denne standard specificerer en metode til bestemmelse af metalliske r?rs evne til at gennemg? plastisk form?ndring ved fladtrykning. R?rene skal have et cirkul?rt tv?rsnit med en udvendig diameter, der ikke er st?rre end 400 mm og en godstykkelse, der ikke er st?rre end 15 % af den udvendige diameter.Intervallet for den udvendige diameter eller godstykkelse, for hvilken denne standard g?lder, kan v?re specificeret n?rme-re i den relevante standard.Fladtrykningspr?vning kan anvendes til at p?vise fejl i et r?r.
信息:ICS:741 CCS发布:1989 实施

ASTM E1652-2014 基金属热电耦, 金属外壳的铂电阻温度计和贵金属热电偶制造中使用的氧化镁和氧化铝粉末及压扁绝缘子的标准规范
简介: 1.1x00a0;This specification covers the requirements for magnesium oxide (MgO) and aluminum oxide (Al2O3) powders and crushable insulators used to manufacture base metal thermocouples, metal-sheathed platinum resistance thermometers (PRTs), noble metal thermocouples, and their respective cables. 1.2x00a0;The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.3x00a0;This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息:ICS:17.200.20 (Temperature-measuring instruments); 29. CCS发布:2014 实施

KS W ISO 1966-2002 航空器电缆的压扁接头
简介:1.1 이 규격은 해당 형식의 케이블에 대해 지정된 도선의 안정화된 온도(즉, 105℃,
信息:ICS:49.06 CCS:V40 发布:2002-09-28 实施:2002-09-28

NF A49-862-1988 钢管.反向压扁试验
简介:
信息:ICS:23.040.10;77.040.10;77.140.75 CCS:H23 发布:1988-10-01 实施:1988-10-20

ASTM E1652-2014a 基金属热电耦, 金属外壳的铂电阻温度计和贵金属热电偶制造中使用的氧化镁和氧化铝粉末及压扁绝缘子的标准规范
简介: 1.1x00a0;This specification covers the requirements for magnesium oxide (MgO) and aluminum oxide (Al2O3) powders and crushable insulators used to manufacture base metal thermocouples, metal-sheathed platinum resistance thermometers (PRTs), noble metal thermocouples, and their respective cables. 1.2x00a0;The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.3x00a0;This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息:ICS:17.200.20 (Temperature-measuring instruments); 29. CCS发布:2014 实施

KS B ISO 8492-2001 金属材料.管材.压扁试验
简介:이 규격은 원형 단면의 금속관을 편평해지도록 납작하게 눌렀을 때 소성 변형에 대한 능력을
信息:ICS:77.040 CCS:H26 发布:2001-12-31 实施:2001-12-31

NC 09-04-35-1987 模具统一原理系统.冲模,压模和机械装置.机械装置.扁头固定支撑.主要尺寸和设计规格
简介:Esta norma establece las especificaciones de proyecto de los apoyos regulables con cabeza moleteada utilizadas para los dispositivos de maquinado.
信息:ICSCCS发布:1987-9-1 实施

BS EN ISO 8492-2013 金属材料.管材.压扁试验
简介:
信息:ICS:77.040.10 CCS:H23 发布:2013-11-30 实施:2013-11-30

KS B ISO 8492-2001 金属材料.管材.压扁试验
简介:이 규격은 원형 단면의 금속관을 편평해지도록 납작하게 눌렀을 때 소성 변형에 대한 능력을
信息:ICS:77.040 CCS:H26 发布:2001-12-31 实施:2001-12-31

QC/T 345-1999 轴用压扁钢丝挡圈
简介:
信息:ICSCCS:T31 发布:1987-12-31 实施:1988-07-01

检测流程

1、确认客户委托,寄样。

2、到样之后,确定具体的试验项目以及试验方案。

3、实验室报价。

4、签订保密协议,进行试验。

5、完成试验,确定检测报告

6、后期技术服务

友情提示:暂不接受个人委托测试

以上是关于"压扁检测标准"的介绍,如有其他问题可以咨询工程师为您服务!

实验室仪器

实验室仪器

压扁检测标准

© 2024 北检(北京)检测技术研究院 ALL RIGHTS RESERVED