钢的脱碳层深度检测标准

原创来源：北检院发布时间：2023-02-09 06:30:10 点击数：

全国服务领域：河北、山西、黑龙江、吉林、辽宁、江苏、浙江、安徽、福建、江西、山东、河南、湖北、湖南、广东、海南、四川、贵州、云南、陕西、甘肃、青海、台湾、内蒙古、广西、西藏、宁夏、新疆、北京、天津、上海、重庆、香港、澳门

钢的脱碳层深度检测标准相关信息

GB/T 224-2019 钢的脱碳层深度测定法
简介：
信息：ICS：77.040.99 CCS：H24 发布：2019-06-04 00:00:00.0 实施：2020-05-01 00:00:00.0

GB/T 224-2008 钢的脱碳层深度测定法
简介：本标准规定了钢的脱碳层术语和定义、测定方法和试验报告等。本标准规定的方法适用于测定钢材（坯）及其零件的脱碳层深度。
信息：ICS：77.040.99 CCS：H24 发布：2008-08-05 实施：2009-04-01

GB/T 224-1987 钢的脱碳层深度测定法
简介： 本标准规定的方法适用于测定钢材（坯）及其零件的脱碳层深度。本标准等效采用国际标准ISO3887-1976《钢——非合金和低合金脱碳层深度的测定》。
信息：ICS：77.040.30 CCS：H24 发布：1987-12-07 实施：1989-01-01

BS EN ISO 3887-2018 钢.脱碳层深度的测定
简介：
信息：ICS：77.040.99;77.080.20 CCS：H11 发布：2018-02-19 实施：2018-02-19

ASTM E1077-2014 评估钢样品脱碳层深度的标准试验方法
简介： 5.1x00a0;These test methods are used to detect surface losses in carbon content due to heating at elevated temperatures, as in hot working or heat treatment. 5.2x00a0;Results of such tests may be used to qualify material for shipment according to agreed upon guidelines between purchaser and manufacturer, for guidance as to machining allowances, or to assess the influence of processing upon decarburization tendency. 5.3x00a0;Screening tests are simple, fast, low-cost tests designed to separate non-decarburized samples from those with appreciable decarburization. Based on the results of such tests, the other procedures may be utilized as applicable. 5.4x00a0;Microscopical tests require a metallographically polished cross section to permit reasonably accurate determination of the depth and nature of the decarburization present. Several methods may be employed for estimation of the depth of decarburization. The statistical accuracy of each varies with the amount of effort expended. 5.5x00a0;Microindentation hardness methods are employed on polished cross sections and are most suitable for hardened specimens with reasonably uniform microstructures. This procedure can be used to define the depth to a specific minimum hardness or the depth to a uniform hardness. 5.6x00a0;Chemical analytical methods are limited to specimens with simple, uniform shapes and are based on analysis of incremental turnings or after milling at fixed increments. 5.7x00a0;Microscopical tests are generally satisfactory for determining the suitability of material for intended use, specification acceptance, manufacturing control, development, or research. 1.1x00a0;These test methods cover procedures for estimating the depth of decarburization of steels irrespective of the composition, matrix microstructure, or section shape. The following basic procedures may be used: 1.1.1x00a0;Screening methods. 1.1.2x00a0;Microscopical methods. 1.1.3x00a0;Microindentation hardness methods. 1.1.4x00a0;Chemical analysis methods. 1.2x00a0;In case of a dispute, the rigorous quantitative or lineal analysis method (see 7.3.5 and 7.3.6) shall be the referee method. These methods can be employed with any cross-sectional shape. The chemical analytical methods generally reveal a greater depth of decarburization than the microscopical methods but are limited to certain simple shapes and by availability of equipment. These techniques are generally reserved for research studies. The microindentation hardness method is suitable for accurate measurements of hardened structures with relatively homogeneous microstructures. 1.3x00a0;The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.4x00a0;This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：77.080.20 (Steels) CCS：发布：2014 实施：

TCVN 4507-2008 钢.脱碳层深度的测定
简介：
信息：ICS： CCS：发布：2008 实施：

BS EN ISO 3887-2003 钢.脱碳层深度的测定
简介：This International Standard defines decarburization and specifies three methods of measuring the depth of decarburization of non-alloy and low-alloy steels.
信息：ICS：77.040.99 CCS：H11 发布：2003-04-17 实施：2003-04-17

EN ISO 3887-2003 钢.脱碳层深度的测定 ISO 3887-2003
简介：
信息：ICS：77.040.99 CCS：发布：2003-03-01 实施：

KS D 0216-2001(2020) 钢之脱碳层深度测定法
简介：
信息：ICS： CCS：发布：2001-11-06 实施：

CNS 10169-1983 钢之脱碳层深度测定法
简介：本标准规定钢之脱碳层深度测定方法。
信息：ICS：19.100 CCS：发布：1983-04-13 实施：1983-04-13

JIS G0558-1977 钢的脱碳层深度的测定方法
简介：
信息：ICS：77.040.30;77.080.20 CCS：J36 发布：1977-08-01 实施：1977-08-01

GOST 1763-1968 钢.脱碳层深度的测定方法
简介：Настоящий стандарт распространяется на деформируемые стали: конструкционные - углеродистые и легированные с содержанием углерода не мен
信息：ICS：77.080.20 CCS：发布：1968 实施：1971-01-01