脱碳与渗碳检测标准

原创来源：北检院发布时间：2023-02-12 19:02:49 点击数：

全国服务领域：河北、山西、黑龙江、吉林、辽宁、江苏、浙江、安徽、福建、江西、山东、河南、湖北、湖南、广东、海南、四川、贵州、云南、陕西、甘肃、青海、台湾、内蒙古、广西、西藏、宁夏、新疆、北京、天津、上海、重庆、香港、澳门

脱碳与渗碳检测标准相关信息

ASTM F2328-17(2022) 测定硬化和回火螺纹钢螺栓、螺钉、螺柱和螺母中脱碳和渗碳的标准试验方法
简介：
信息：ICS：21.060.01 CCS：发布：2022-08-01 实施：

ASTM F2328M-2005 淬火和回火的螺纹钢螺栓、螺钉和螺柱的脱碳和渗碳性测定的标准试验方法(米制)
简介：1.1 This test method covers procedures for measuring, classifying, and determining the presence of decarburization and carburization in the threaded section of hardened and tempered metric steel bolts, screws, studs, and similar parts which have been heated to facilitate fabrication or to modify its mechanical properties. This test method is not intended to address products which are intentionally carburized to achieve specific results.1.2 Two routine methods are described for measuring the limits of and determining the presence of decarburization or carburization; the Optical Method and the Microindentation Method 1. Either method is appropriate for routine examinations. The Microindentation Method 2 shall be considered the referee method.1.3 For the purpose of these tests, there are three classes of hardened and tempered steel products for which specific measurements must be made with respect to their physical properties.1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：21.060.01 (Fasteners in general); 77.140.20 (Steel CCS：J13 发布：2005 实施：

ASTM F2328M-17(2022) 测定硬化和回火螺纹钢螺栓、螺钉、螺柱和螺母脱碳和渗碳的标准试验方法（米制）
简介：
信息：ICS：21.060.01 CCS：发布：2022-08-01 实施：

ASTM F2328-2005(2011) 测定硬化和回火螺纹钢螺栓,螺钉和螺柱螺栓的脱碳和渗碳的标准试验方法
简介：Decarburization and carburization are two surface conditions created, either intentionally or unintentionally, as with a pre-existing condition created during the rod rolling process, the rod/wire annealing process, or while heat treating threaded steel products. Too much of either will adversely affect the safety and performance of the threaded product. Therefore, limits have been established for three different product groups: the harder and greater the tensile strength of the product, the more susceptible to failure the product becomes if these limits are exceeded. When testing to a particular product specification that lists the dimensions and microindentation data to be used, that data shall take precedence over the tables in this test method. There are only two viable methods available to detect these deficiencies, either by the visual method or the microindentation method. Both methods are used for routine inspections when evaluations are conducted at a single location on the product sample. Because an evaluation at a specific location may not be representative of the whole part, the referee method employs the microindentation method taken as an average of evaluations conducted on four adjacent threads. This procedure significantly reduces the random test variables when compared to testing on a single thread. Specifying this test method does not specify or imply that testing shall be for either decarburization or carburization alone or for both conditions. When either test method is performed, both conditions will be apparent and shall be reported. For example, if an order is placed to test for decarburization and none is found, but the presence of carburization is detected, it shall be reported on the test report that carburization was found.1.1 This test method covers procedures for measuring, classifying, and determining the presence of decarburization and carburization in the threaded section of hardened and tempered inch series steel bolts, screws, studs, and similar parts which have been heated to facilitate fabrication or to modify its mechanical properties. This test method is not intended to address products which are intentionally carburized to achieve specific results. 1.2 Two routine methods are described for measuring the limits of and determining the presence of decarburization or carburizationthe optical method and the microindentation method 1. Either method is appropriate for routine examinations. The microindentation method 2 shall be considered the referee method. 1.3 For the purpose of these tests, there are three classes of hardened and tempered steel products for which specific measurements must be made with respect to their physical properties. 1.4 The values stated in inch-pound units are to be regarded as standard. No other units of measurement are included in this standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：77.140.20 (Steels of high quality) CCS：J13 发布：2005 实施：

ASTM F2328M-17 硬化和钢化螺纹钢螺栓螺钉螺柱和螺母（公制）的脱碳和渗碳测定的标准试验方法
简介：
信息：ICS：21.060.01 CCS：发布：2017-09-01 实施：

ASTM F2328-04 螺钉和螺柱用淬火和回火螺纹钢螺栓脱碳和渗碳测定的标准试验方法
简介：
信息：ICS：21.060.01 CCS：发布：2004-07-01 实施：

ASTM F2328-17 硬化和钢化螺纹钢螺栓螺钉螺柱和螺母的脱碳和渗碳确定标准试验方法
简介：
信息：ICS：21.060.01 CCS：发布：2017-09-01 实施：

ASTM F2328M-04 螺钉和螺柱用淬火和回火螺纹钢螺栓脱碳和渗碳测定的标准试验方法[米制]
简介：
信息：ICS：21.060.01 CCS：发布：2004-07-01 实施：

ASTM F2328M-14 硬化和钢化螺纹钢螺栓螺钉螺柱和螺母的脱碳和渗碳测定标准试验方法
简介：
信息：ICS：21.060.01 CCS：发布：2014-08-01 实施：

ASTM F2328-2004 淬火和回火的螺纹钢螺栓、螺母和螺柱的脱碳和渗碳性测定的标准试验方法
简介：1.1 This test method covers procedures for measuring, classifying, and determining the presence of decarburization and carburization in the threaded section of hardened and tempered inch series steel bolts, screws, studs, and similar parts which have been heated to facilitate fabrication or to modify its mechanical properties. This test method is not intended to address products which are intentionally carburized to achieve specific results.1.2 Two routine methods are described for measuring the limits of and determining the presence of decarburization or carburization-the optical method and the microindentation method 1. Either method is appropriate for routine examinations. The microindentation method 2 shall be considered the referee method.1.3 For the purpose of these tests, there are three classes of hardened and tempered steel products for which specific measurements must be made with respect to their physical properties.1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：21.060.01 (Fasteners in general); 77.140.20 (Steel CCS：J13 发布：2004 实施：

ASTM F2328-14 硬化和钢化螺纹钢螺栓螺钉螺柱和螺母的脱碳和渗碳确定标准试验方法
简介：
信息：ICS：21.060.01 CCS：发布：2014-08-01 实施：

ASTM F2328M-2004 淬火和回火的螺纹钢螺栓、螺钉和螺柱的脱碳和渗碳性测定的标准试验方法(米制)
简介：1.1 This test method covers procedures for measuring, classifying, and determining the presence of decarburization and carburization in the threaded section of hardened and tempered metric steel bolts, screws, studs, and similar parts which have been heated to facilitate fabrication or to modify its mechanical properties. This test method is not intended to address products which are intentionally carburized to achieve specific results.1.2 Two routine methods are described for measuring the limits of and determining the presence of decarburization or carburization; the Optical Method and the Microindentation Method 1. Either method is appropriate for routine examinations. The Microindentation Method 2 shall be considered the referee method.1.3 For the purpose of these tests, there are three classes of hardened and tempered steel products for which specific measurements must be made with respect to their physical properties.1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：21.060.01 (Fasteners in general); 77.140.20 (Steel CCS：J13 发布：2004 实施：

ASTM F2328M-07(2014) 测定淬火和回火螺纹钢螺栓、螺钉和螺柱中脱碳和渗碳的标准试验方法&40；公制和41
简介：
信息：ICS：21.060.01 CCS：发布：2014-02-01 实施：

SAE ARP 1341B-2001 碳钢和低合金钢成品零件脱碳和渗碳的测定
简介：This document provides a recommended practice for determining decarburization and carburization in heat treated carbon and low-alloy steel parts other than case hardened parts. It is not applicable to raw materials.
信息：ICS：49.025.10 CCS：V22 发布：2001-04-01 实施：

ASTM F2328M-2014 淬火和回火的螺纹钢螺栓, 螺钉, 螺柱和螺母的脱碳和渗碳性测定的标准试验方法 (米制)
简介： 4.1x00a0;Decarburization and carburization are two surface conditions created, either intentionally or unintentionally, as with a pre-existing condition created during the rod rolling process, the rod/wire annealing process, or while heat treating threaded steel products. Too much of either will adversely affect the safety and performance of the threaded product. Therefore, limits have been established for four different product groups: the harder and greater the tensile strength of the product, the more susceptible to failure the product becomes if these limits are exceeded. 4.2x00a0;When testing to a particular product specification that lists the dimensions and microindentation data to be used, that data shall take precedence over the tables in this test method. 4.3x00a0;There are only two viable methods available to detect these deficiencies: either by the visual method or the microindentation method. Both methods are used for routine inspections when evaluations are conducted at a single location on the product sample. Because an evaluation at a specific location may not be representative of the whole part, the referee method employs the microindentation method taken as an average of evaluations conducted on four adjacent threads. This procedure significantly reduces random test variables when compared to testing on a single thread.x02d9; 4.4x00a0;Specifying this test method does not specify or imply that testing shall be for either decarburization or carburization alone or for both conditions. When either test method is performed, both conditions will be apparent and shall be reported. For example, if an order is placed to test for decarburization and none is found but the presence of decarburization is detected, it shall be reported on the test report that carburization was found. 1.1x00a0;This test method covers procedures for measuring, classifying, and determining the presence of decarburization and carburization in the threaded section of hardened and tempered metric steel bolts, screws, studs, nuts and similar parts which have been heated to facilitate fabrication or to modify their mechanical properties. This test method is not intended to address products which are intentionally carburized to achieve specific results. 1.2x00a0;Two routine methods are described for measuring the limits of and determining the presence of decarburization or carburization; the Optical Method and the Microindentation Method 1. Either method is appropriate for routine examinations. The Microindentation Method 2 shall be considered the referee method. 1.3x00a0;For the purpose of these tests, there are five classes of hardened and tempered steel products for which specific measurements must be made with respect to their physical properties. 1.4x00a0;The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.5x00a0;This standard does not purport to address all of the safety concer......
信息：ICS：21.060.01 (Fasteners in general); 77.140.20 (Steel CCS：发布：2014 实施：

ASTM F2328-2014 淬火和回火的螺纹钢螺栓, 螺钉, 螺柱和螺母的脱碳和渗碳性测定的标准试验方法
简介： 4.1x00a0;Decarburization and carburization are two surface conditions created, either intentionally or unintentionally, as with a pre-existing condition created during the rod rolling process, the rod/wire annealing process, or while heat treating threaded steel products. Too much of either will adversely affect the safety and performance of the threaded product. Therefore, limits have been established for three different product groups: the harder and greater the tensile strength of the product, the more susceptible to failure the product becomes if these limits are exceeded. 4.2x00a0;When testing to a particular product specification that lists the dimensions and microindentation data to be used, that data shall take precedence over the tables in this test method. 4.3x00a0;There are only two viable methods available to detect these deficiencies, either by the visual method or the microindentation method. Both methods are used for routine inspections when evaluations are conducted at a single location on the product sample. 4.3.1x00a0;Because an evaluation at a specific location may not be representative of the whole part, the referee method employs the microindentation method taken as an average of evaluations conducted on four adjacent threads. This procedure significantly reduces the random test variables when compared to testing on a single thread. 4.4x00a0;Specifying this test method does not specify or imply that testing shall be for either decarburization or carburization alone or for both conditions. When either test method is performed, both conditions will be apparent and shall be reported. For example, if an order is placed to test for decarburization and none is found, but the presence of carburization is detected, it shall be reported on the test report that carburization was found. 1.1x00a0;This test method covers procedures for measuring, classifying, and determining the presence of decarburization and carburization in the threaded section of hardened and tempered inch series steel bolts, screws, studs, nuts, and similar parts which have been heated to facilitate fabrication or to modify their mechanical properties. This test method is not intended to address products which are intentionally carburized to achieve specific results. 1.2x00a0;Two routine methods are described for measuring the limits of and determining the presence of decarburization or carburizationx2014;the optical method and the microindentation method 1. Either method is appropriate for routine examinations. The microindentation method 2 shall be considered the referee method. 1.3x00a0;For the purpose of these tests, there are four classes of hardened and tempered steel products for which specific measurements must be made with respect to their physical properties. 1.4x00a0;The values stated in inch-pound units are to be regarded as standard. No other units of measurement are included in this standard. 1.5x00a0;This standard does not purport to address all of the safety concerns, if any, as......
信息：ICS：21.060.01 (Fasteners in general); 77.140.20 (Steel CCS：发布：2014 实施：

ASTM F2328M-07(2013) 螺钉和螺柱用淬火和回火螺纹钢螺栓脱碳和渗碳测定的标准试验方法（米制）
简介：
信息：ICS：21.060.01 CCS：发布：2013-08-01 实施：

ASTM F2328-05(2011) 螺钉和螺柱用淬火和回火螺纹钢螺栓脱碳和渗碳测定的标准试验方法
简介：
信息：ICS：21.060.01 CCS：发布：2011-05-01 实施：

ASTM F2328M-07 螺钉和螺柱用淬火和回火螺纹钢螺栓脱碳和渗碳测定的标准试验方法[米制]
简介：
信息：ICS：21.060.01 CCS：发布：2007-10-01 实施：

ASTM F2328M-2007 淬火和回火的螺纹钢螺栓、螺钉和螺柱的脱碳和渗碳性测定的标准试验方法(米制)
简介：1.1 This test method covers procedures for measuring, classifying, and determining the presence of decarburization and carburization in the threaded section of hardened and tempered metric steel bolts, screws, studs, and similar parts which have been heated to facilitate fabrication or to modify its mechanical properties. This test method is not intended to address products which are intentionally carburized to achieve specific results.1.2 Two routine methods are described for measuring the limits of and determining the presence of decarburization or carburization; the Optical Method and the Microindentation Method 1. Either method is appropriate for routine examinations. The Microindentation Method 2 shall be considered the referee method.1.3 For the purpose of these tests, there are four classes of hardened and tempered steel products for which specific measurements must be made with respect to their physical properties.1.4 solely-SI-units;This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：21.060.01 (Fasteners in general); 77.140.20 (Steel CCS：J13 发布：2007 实施：

ASTM F2328M-2007(2014) 测定公制41淬火与回火螺纹钢螺栓, 螺钉和螺柱40脱碳和渗碳性的标准试验方法
简介： 4.1x00a0;Decarburization and carburization are two surface conditions created, either intentionally or unintentionally, as with a pre-existing condition created during the rod rolling process, the rod/wire annealing process, or while heat treating threaded steel products. Too much of either will adversely affect the safety and performance of the threaded product. Therefore, limits have been established for four different product groups: the harder and greater the tensile strength of the product, the more susceptible to failure the product becomes if these limits are exceeded. 4.2x00a0;When testing to a particular product specification that lists the dimensions and microindentation data to be used, that data shall take precedence over the tables in this test method. 4.3x00a0;There are only two viable methods available to detect these deficiencies: either by the visual method or the microindentation method. Both methods are used for routine inspections when evaluations are conducted at a single location on the product sample. Because an evaluation at a specific location may not be representative of the whole part, the referee method employs the microindentation method taken as an average of evaluations conducted on four adjacent threads. This procedure significantly reduces random test variables when compared to testing on a single thread.x02d9; 4.4x00a0;Specifying this test method does not specify or imply that testing shall be for either decarburization or carburization alone or for both conditions. When either test method is performed, both conditions will be apparent and shall be reported. For example, if an order is placed to test for decarburization and none is found but the presence of decarburization is detected, it shall be reported on the test report that carburization was found. 1.1x00a0;This test method covers procedures for measuring, classifying, and determining the presence of decarburization and carburization in the threaded section of hardened and tempered metric steel bolts, screws, studs, and similar parts which have been heated to facilitate fabrication or to modify its mechanical properties. This test method is not intended to address products which are intentionally carburized to achieve specific results. 1.2x00a0;Two routine methods are described for measuring the limits of and determining the presence of decarburization or carburization; the Optical Method and the Microindentation Method 1. Either method is appropriate for routine examinations. The Microindentation Method 2 shall be considered the referee method. 1.3x00a0;For the purpose of these tests, there are four classes of hardened and tempered steel products for which specific measurements must be made with respect to their physical properties. 1.4x00a0;The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.5x00a0;This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：21.060.01 (Fasteners in general); 77.140.20 (Steel CCS：J13 发布：2007 实施：

ASTM F2328M-2007(2013) 测定公制淬火与回火螺纹钢螺栓, 螺钉和螺柱脱碳和渗碳性的标准试验方法
简介： 4.1x00a0;Decarburization and carburization are two surface conditions created, either intentionally or unintentionally, as with a pre-existing condition created during the rod rolling process, the rod/wire annealing process, or while heat treating threaded steel products. Too much of either will adversely affect the safety and performance of the threaded product. Therefore, limits have been established for four different product groups: the harder and greater the tensile strength of the product, the more susceptible to failure the product becomes if these limits are exceeded. 4.2x00a0;When testing to a particular product specification that lists the dimensions and microindentation data to be used, that data shall take precedence over the tables in this test method. 4.3x00a0;There are only two viable methods available to detect these deficiencies: either by the visual method or the microindentation method. Both methods are used for routine inspections when evaluations are conducted at a single location on the product sample. Because an evaluation at a specific location may not be representative of the whole part, the referee method employs the microindentation method taken as an average of evaluations conducted on four adjacent threads. This procedure significantly reduces random test variables when compared to testing on a single thread.x02d9; 4.4x00a0;Specifying this test method does not specify or imply that testing shall be for either decarburization or carburization alone or for both conditions. When either test method is performed, both conditions will be apparent and shall be reported. For example, if an order is placed to test for decarburization and none is found but the presence of decarburization is detected, it shall be reported on the test report that carburization was found. 1.1x00a0;This test method covers procedures for measuring, classifying, and determining the presence of decarburization and carburization in the threaded section of hardened and tempered metric steel bolts, screws, studs, and similar parts which have been heated to facilitate fabrication or to modify its mechanical properties. This test method is not intended to address products which are intentionally carburized to achieve specific results. 1.2x00a0;Two routine methods are described for measuring the limits of and determining the presence of decarburization or carburization; the Optical Method and the Microindentation Method 1. Either method is appropriate for routine examinations. The Microindentation Method 2 shall be considered the referee method. 1.3x00a0;For the purpose of these tests, there are four classes of hardened and tempered steel products for which specific measurements must be made with respect to their physical properties. 1.4x00a0;The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.5x00a0;This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：21.060.01 (Fasteners in general); 77.140.20 (Steel CCS：J13 发布：2007 实施：

ASTM F2328M-06 螺钉和螺柱用淬火和回火螺纹钢螺栓脱碳和渗碳测定的标准试验方法[米制]
简介：
信息：ICS：21.060.01 CCS：发布：2006-06-01 实施：

ASTM F2328M-2006 淬火和回火的螺纹钢螺栓、螺钉和螺柱的脱碳和渗碳性测定的标准试验方法(米制)
简介：1.1 This test method covers procedures for measuring, classifying, and determining the presence of decarburization and carburization in the threaded section of hardened and tempered metric steel bolts, screws, studs, and similar parts which have been heated to facilitate fabrication or to modify its mechanical properties. This test method is not intended to address products which are intentionally carburized to achieve specific results.1.2 Two routine methods are described for measuring the limits of and determining the presence of decarburization or carburization; the Optical Method and the Microindentation Method 1. Either method is appropriate for routine examinations. The Microindentation Method 2 shall be considered the referee method.1.3 For the purpose of these tests, there are four classes of hardened and tempered steel products for which specific measurements must be made with respect to their physical properties.This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：21.060.01 (Fasteners in general); 77.140.20 (Steel CCS：J13 发布：2006 实施：

ASTM F2328M-05 螺钉和螺柱用淬火和回火螺纹钢螺栓脱碳和渗碳测定的标准试验方法[米制]
简介：
信息：ICS：21.060.01 CCS：发布：2005-06-15 实施：

ASTM F2328-05 螺钉和螺柱用淬火和回火螺纹钢螺栓脱碳和渗碳测定的标准试验方法
简介：
信息：ICS：21.060.01 CCS：发布：2005-05-01 实施：

ASTM F2328-2005 淬火和回火的螺纹钢螺栓、螺母和螺柱的脱碳和渗碳性测定的标准试验方法
简介：Decarburization and carburization are two surface conditions created, either intentionally or unintentionally, as with a pre-existing condition created during the rod rolling process, the rod/wire annealing process, or while heat treating threaded steel products. Too much of either will adversely affect the safety and performance of the threaded product. Therefore, limits have been established for three different product groups: the harder and greater the tensile strength of the product, the more susceptible to failure the product becomes if these limits are exceeded. When testing to a particular product specification that lists the dimensions and microindentation data to be used, that data shall take precedence over the tables in this test method. There are only two viable methods available to detect these deficiencies, either by the visual method or the microindentation method. Both methods are used for routine inspections when evaluations are conducted at a single location on the product sample. 4.3.1 Because an evaluation at a specific location may not be representative of the whole part, the referee method employs the microindentation method taken as an average of evaluations conducted on four adjacent threads. This procedure significantly reduces the random test variables when compared to testing on a single thread. Specifying this test method does not specify or imply that testing shall be for either decarburization or carburization alone or for both conditions. When either test method is performed, both conditions will be apparent and shall be reported. For example, if an order is placed to test for decarburization and none is found, but the presence of carburization is detected, it shall be reported on the test report that carburization was found.1.1 This test method covers procedures for measuring, classifying, and determining the presence of decarburization and carburization in the threaded section of hardened and tempered inch series steel bolts, screws, studs, and similar parts which have been heated to facilitate fabrication or to modify its mechanical properties. This test method is not intended to address products which are intentionally carburized to achieve specific results.1.2 Two routine methods are described for measuring the limits of and determining the presence of decarburization or carburization-the optical method and the microindentation method 1. Either method is appropriate for routine examinations. The microindentation method 2 shall be considered the referee method.1.3 For the purpose of these tests, there are three classes of hardened and tempered steel products for which specific measurements must be made with respect to their physical properties.This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：21.060.01 (Fasteners in general); 77.140.20 (Steel CCS：J13 发布：2005 实施：