贮存稳定性检测标准

原创来源：北检院发布时间：2023-02-22 19:57:31 点击数：

全国服务领域：河北、山西、黑龙江、吉林、辽宁、江苏、浙江、安徽、福建、江西、山东、河南、湖北、湖南、广东、海南、四川、贵州、云南、陕西、甘肃、青海、台湾、内蒙古、广西、西藏、宁夏、新疆、北京、天津、上海、重庆、香港、澳门

贮存稳定性检测标准相关信息

GB/T 33327-2016 紫外光固化涂料贮存稳定性的评定
简介：
信息：ICS：87.040 CCS：G50 发布：2016-12-13 00:00:00.0 实施：2017-07-01 00:00:00.0

ASTM F1104-02(2008) 贮存稳定性试验用液态水基飞机清洗剂制备的标准试验方法
简介：
信息：ICS：49.040 CCS：发布：2008-04-01 实施：

ISO 8130-8:1994 涂层粉末Spart 8:热固性粉末贮存稳定性的评估
简介：
信息：ICS：87.040 CCS：发布：1994-08-11 实施：

GB/T 21782.8-2008 粉末涂料.第8部分:热固性粉末贮存稳定性的评定
简介：GB/T 21782的本部分规定了热固性粉末贮存稳定性的评定。其中规定了热固性粉末涂料的物理状态和化学活性保持性以及形成令人满意的最终涂层的能力的评价试验程序。不同性能变化之间的相互关系是不能预料的。同样，在不同的贮存条件下，所得到的试验结果也不存在相关性。由本部分规定的程序所得到的试验结果说明了粉末涂料在施工前所能耐受存储时限的能力。
信息：ICS：13.300 CCS：G50;A80 发布：2008-05-12 实施：2008-09-01

NY/T 1427-2007 农药常温贮存稳定性试验通则
简介： 1.1 本标准规定了农药常温贮存稳定性试验方法、试验报告编写以及产品保质期的基本要求。 1.2 本标准适用于为申请农药制剂正式登记而进行的常温贮存稳定性试验。
信息：ICS：65.100.01 CCS：B17 发布：2007-09-14 实施：2007-12-01

JIS K7617-1994 贮存经过显影处理的普通摄影胶卷及印相纸的包装材料对照片画面稳定性影响试验方法
简介：
信息：ICS：37.040.30 CCS：G80 发布：1994-03-01 实施：1994-03-01

GB 6753.3-1986 涂料贮存稳定性试验方法
简介：
信息：ICS： CCS：发布：1986-08-26 实施：1987-08-01

SH/T 0099.5-2005 乳化沥青贮存稳定性测定法
简介： 本标准规定了乳化沥青贮存24h的贮存稳定性的测定方法。本标准适用于测定乳化沥青贮存24h的贮存稳定性。本标准未涉及有关使用的安全规定，标准使用者有责任在使用前制定合适的安全应用规程。
信息：ICS：75.140 CCS：E43;E30 发布：2005-11-28 实施：2006-06-01

HB 5329-1993 航空用厌氧胶贮存稳定性.试验方法
简介：本标准规定了航空用厌氧胶贮存稳定性试验方法的设备与材料、试件与试样、试验条件、试验程序、试验结果的处理和试验报告。　　本标准适用于测定未聚合的厌氧胶在一定条件下的贮存稳定性。
信息：ICS： CCS：V13 发布：1993-11-05 实施：1994-03-01

GB/T 6753.3-1986 涂料贮存稳定性试验方法
简介： 本标准适用于液态色漆和清漆在密闭容器中，放置自然环境或加速条件下贮存后，测定所产生的粘度变化，色漆中颜料沉降，色漆重新混合以适于使用的难易程度以及其他按产品规定所需检测的性能变化，作为色漆和清漆贮存稳定性的试验方法。
信息：ICS：87.040 CCS：G50 发布：1986-08-26 实施：1987-08-01

ASTM D4144-94(2005) 紫外光固化涂料贮存稳定性的评定
简介：
信息：ICS：87.040 CCS：发布：2005-05-15 实施：

SH/T 0568-1993 油包水型乳化液贮存稳定性测定法（烘箱法）
简介：
信息：ICS： CCS：E30 发布：1993-08-19 实施：1994-05-01

ASTM D4625-21 43℃下中间馏分燃料贮存稳定性的标准试验方法摄氏度（110度） °F）
简介：
信息：ICS：75.080 CCS：发布：2021-10-01 实施：

ASTM D3707-89(2005)e1 用烘箱试验法测定油包水乳液贮存稳定性的标准试验方法
简介：
信息：ICS：75.100 CCS：发布：2005-05-01 实施：

ASTM F1104-87(1998) 贮存稳定性试验用液态水基飞机清洗剂制备的标准试验方法
简介：
信息：ICS：49.040 CCS：发布：1993-01-01 实施：

GMKOREA EDS-T-7963-2020 涂料贮存稳定性的试验方法（第5版；英语/韩语）
简介：
信息：ICS：87.040 CCS：G51 发布：2020-12-01 实施：

ASTM D4625-04 43℃和176℃下馏出燃料贮存稳定性的标准试验方法；C（110和176；（F）
简介：
信息：ICS：75.080 CCS：发布：2004-06-01 实施：

ONORM C 9233-1990 路用沥青乳液测试．筛渣和贮存稳定性
简介：Diese ?NORM dient der Feststellung des Anteiles an agglomerierten Bitumenteilchen in einer Bitumenemui-sion sowohl im Anlieferungszustand als auch nach einer vorgegebenen Lagerungsdauer.Diese ?NORM ist anwendbar für anionische, kationische und nichtionische Bitumenemulsionen.
信息：ICS： CCS：发布：1990-6-1 实施：

T/CSTM 00225-2020 水性汽车涂料贮存稳定性的测试及评价方法
简介：本标准规定了测试及评价水性汽车涂料贮存稳定性的原理、仪器设备、取样、试验步骤、结论性评定、精密度、试验报告等内容。本标准适用于水性汽车涂料（原厂）贮存稳定性的测试及评价。其他领域的水性涂料贮存稳定性的测试及评价也可参考本标准。
信息：ICS：87.040 CCS：C264 发布：2020-04-14 实施：2020-04-15

ASTM D4625-2004(2009) 馏分燃料在43°C (110°F)贮存稳定性的标准试验方法
简介：Fuel oxidation and other degradative reactions leading to formation of sediment (and color) are mildly accelerated by the test conditions compared with typical storage conditions. Test results have been shown to predict storage stability more reliably than other more accelerated tests. See Appendix X1 for information on the correlation of test results with actual field storage. Because the storage periods are long (4 to 24 weeks), the test method is not suitable for quality control testing, but does provide a tool for research on storage properties of fuels. Because environmental effects and the materials and nature of tank construction affect storage stability, the results obtained by this test are not necessarily the same as those obtained during storage in a specific field storage situation.1.1 This test method covers a method for evaluating the inherent storage stability of distillate fuels having flash points above 38x00B0;C (100x00B0;F), by Test Methods D 93, and 90 % distilled points below 340x00B0;C (644x00B0;F), by Test Method D 86. Note 18212;ASTM specification fuels falling within the scope of this test method are Specification D 396, Grade Nos. 1 and 2; Specification D 975, Grades 1-D and 2-D; and Specification D 2880, Grades 1-GT and 2-GT. 1.2 This test method is not suitable for quality control testing but, rather it is intended for research use to shorten storage time relative to that required at ambient storage temperatures. 1.3 Appendix X1 presents additional information about storage stability and the correlation of Test Method D 4625 results with sediment formation in actual field storage. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：75.080 (Petroleum products in general) CCS：E31 发布：2004 实施：

ASTM D3707-1989(2010) 耐热试验法测定油包水乳液贮存稳定性的标准试验方法
简介：This test method indicates the stability of the emulsion during storage and normal usage.1.1 This test method covers the stability of water-in-oil emulsions when held at a constant elevated temperature. 1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：75.100 CCS：E30 发布：1989 实施：

ASTM F1104-02(2019) 贮存稳定性试验用液态水基飞机清洗剂制备的标准试验方法
简介：
信息：ICS：49.040 CCS：发布：2019-05-01 实施：

ASTM D4625-2004 馏分燃料在43℃(100°F)贮存稳定性的标准试验方法
简介：Fuel oxidation and other degradative reactions leading to formation of sediment (and color) are mildly accelerated by the test conditions compared with typical storage conditions. Test results have been shown to predict storage stability more reliably than other more accelerated tests. See Appendix X1 for information on the correlation of test results with actual field storage. Because the storage periods are long (4 to 24 weeks), the test method is not suitable for quality control testing, but does provide a tool for research on storage properties of fuels. Because environmental effects and the materials and nature of tank construction affect storage stability, the results obtained by this test are not necessarily the same as those obtained during storage in a specific field storage situation.1.1 This test method covers a method for evaluating the inherent storage stability of distillate fuels having flash points above 38176;C (100176;F) and 90 % distilled points below 340176;C (644176;F).Note 18212;ASTM specification fuels falling within the scope of this test method are Specification D 396, Grade Nos. 1 and 2; Specification D 975, Grades 1-D and 2-D; and Specification D 2880, Grades 1-GT and 2-GT.1.2 This test method is not suitable for quality control testing but, rather it is intended for research use to shorten storage time relative to that required at ambient storage temperatures.1.3 Appendix X1 presents additional information about storage stability and the correlation of Test Method D 4625 results with sediment formation in actual field storage.1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：75.080 (Petroleum products in general) CCS：E31 发布：2004 实施：

ASTM D3707-1989(2005)e1 耐热试验法测定油包水乳液贮存稳定性的标准试验方法
简介：This test method indicates the stability of the emulsion during storage and normal usage.1.1 This test method covers the stability of water-in-oil emulsions when held at a constant elevated temperature.1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：75.100 (Lubricants, industrial oils and related pr CCS：E30 发布：1989 实施：

ASTM D6654-18 机械泵分配器基本贮存稳定性的标准实施规程
简介：
信息：ICS：19.060 CCS：发布：2018-05-01 实施：

ASTM D4625-03 43℃和176℃下馏出燃料贮存稳定性的标准试验方法；C（110和176；（F）
简介：
信息：ICS：75.080 CCS：发布：2003-11-01 实施：

NF T77-108-1986 工业用碱性硅树脂.乳胶.贮存和离心稳定性的测定
简介：
信息：ICS：71.100.55 CCS：G17 发布：1986-07-01 实施：1986-07-05

ASTM D4625-16 在43摄氏度（110华氏度）下中馏分燃料贮存稳定性的标准试验方法
简介：
信息：ICS：75.080 CCS：发布：2016-12-01 实施：

ASTM F1105-03 贮存稳定性试验用液体型温度敏感型或溶剂型飞机清洗剂制备的标准试验方法
简介：
信息：ICS：49.040 CCS：发布：2003-03-10 实施：

CSN 65 9024-1983 活性染料．贮存稳定性的测定方法
简介：Schváleni ST SEV 3854-82 doporu?ilo ministerstvo pr?myslu ?SRZpracovatel: Sdru?ení pro odbyt dehtov?ch barviv, Pardubice-Rybitví — E. ScherksováPracovník ??adu pro normalizaci a mě?ení: Ing. H. Vonásková
信息：ICS： CCS：发布：1983-11-22 实施：

ASTM D4625-16e1 在43摄氏度（110华氏度）下中馏分燃料贮存稳定性的标准试验方法
简介：
信息：ICS：75.080 CCS：发布：2016-12-01 实施：

ASTM D4625-2003 馏分燃料在43℃(110°F)贮存稳定性的标准试验方法
简介：1.1 This test method covers a method for evaluating the inherent storage stability of distillate fuels having flash points above 38176;C (100176;F) and 90 % distilled points below 340176;C (644176;F).Note 18212;ASTM specification fuels falling within the scope of this test method are Specification D 396, Grade Nos. 1 and 2; Specification D 975, Grades 1-D and 2-D; and Specification D 2880, Grades 1-GT and 2-GT.1.2 This test method is not suitable for quality control testing but, rather it is intended for research use to shorten storage time relative to that required at ambient storage temperatures.1.3 Appendix X1 presents additional information about storage stability and the correlation of Test Method D 4625 results with sediment formation in actual field storage.1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：75.080 (Petroleum products in general) CCS：E31 发布：2003 实施：

NF T30-507-1981 热固性粉末状涂料.贮存稳定性的评价
简介：
信息：ICS：87.040 CCS：G51 发布：1981-09-01 实施：1981-09-26

ASTM D4625-14 43&thinsp下中间馏分燃料贮存稳定性的标准试验方法&度；C（110&thinsp&度；（F）
简介：
信息：ICS：75.080 CCS：发布：2014-12-01 实施：

ASTM D5304-02a 用氧超压评定馏出燃料贮存稳定性的标准试验方法
简介：
信息：ICS：75.080 CCS：发布：2002-12-10 实施：

DIN 52042-1980 沥青粘接剂的检验.乳化液贮存稳定性的测定
简介：Testing of bituminous binders; determination of storage stability of emulsions Essais des liants bitumineux; détermination de la stabilité au stockage des émulsionsAllgemeine Angaben zur Prüfung bitumin?ser Bindemittel sind in DIN 52 000 enthalten.
信息：ICS：5785 CCS：E43 发布：1980-12 实施：

ASTM D4625-2014 中间馏分燃料在43 ℃ (110 ℉)下贮存稳定性的标准试验方法
简介： 5.1x00a0;Fuel oxidation and other degradative reactions leading to formation of sediment (and color) are mildly accelerated by the test conditions compared with typical storage conditions. Test results have been shown to predict storage stability more reliably than other more accelerated tests. See Appendix X1 for information on the correlation of test results with actual field storage. 5.2x00a0;Because the storage periods are long (48201;weeks to 248201;weeks), the test method is not suitable for quality control testing, but does provide a tool for research on storage properties of fuels. 5.3x00a0;Because environmental effects and the materials and nature of tank construction affect storage stability, the results obtained by this test are not necessarily the same as those obtained during storage in a specific field storage situation. 1.1x00a0;This test method covers a method for evaluating the inherent storage stability of distillate fuels having flash points above 388201;x00b0;C (1008201;x00b0;F), by Test Methods D93, and 908201;% distilled points below 3408201;x00b0;C (6448201;x00b0;F), by Test Method D86. Note 1:x00a0;ASTM specification fuels falling within the scope of this test method are Specification D396, Grade Nos. 1 and 2; Specification D975, Grades 1-D and 2-D; and Specification D2880, Grades 1-GT and 2-GT. 1.2x00a0;This test method is not suitable for quality control testing but, rather it is intended for research use to shorten storage time relative to that required at ambient storage temperatures. 1.3x00a0;Appendix X1 presents additional information about storage stability and the correlation of Test Method D4625 results with sediment formation in actual field storage. 1.4x00a0;The values given in SI units are to be regarded as the standard. The values in parentheses are for information only. 1.5x00a0;This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：75.080 CCS：发布：2014 实施：

ASTM D5304-02 用氧超压评定馏出燃料贮存稳定性的标准试验方法
简介：
信息：ICS：75.080 CCS：发布：2002-06-10 实施：

ASTM F1104-2002(R2019) 贮存稳定性试验用液态水基飞机清洗剂制备的标准试验方法
简介：
信息：ICS：49.040 CCS：发布：0000-00-00 实施：0000-00-00

ASTM F1104-02(2013) 贮存稳定性试验用液态水基飞机清洗剂制备的标准试验方法
简介：
信息：ICS：49.040 CCS：发布：2013-12-01 实施：

ASTM F1104-02 贮存稳定性试验用液态水基飞机清洗剂制备的标准试验方法
简介：
信息：ICS：49.040 CCS：发布：2002-05-10 实施：

HG/T 4920-2016 纺织染整助剂贮存稳定性的测定
简介：
信息：ICS： CCS：发布：实施：2016-07-01

EN 1429-2013 沥青和沥青粘合剂.沥青乳剂筛分残留的测定和筛分贮存稳定性的测定
简介：This European Standard specifies methods utilising sieving for the determination of the quantity of coarse particles of binder present in bitumen emulsions, and for the determination of storage stability.
信息：ICS：75.140;91.100.50 CCS：E43 发布：2013-06-01 实施：2013-06

GOST R 51909-2002 机器,仪器与其他工业产品的环境稳定性测试方法.运输与贮存测试
简介：
信息：ICS：21.020 CCS：发布：2002 实施：2003-07-01

ASTM D7603-2013 测定汽车齿轮油贮存稳定性和兼容性的标准试验方法
简介： 5.1x00a0;To avoid equipment failure, a gear oil should remain a homogeneous liquid and the performance-enhancing additives should not separate out when the oil is stored for an extended period of time. 5.2x00a0;In addition, because different oils are often mixed when topping off, gear oils from different manufacturers, or containing different base fluids or performance-enhancing additives should be completely miscible and compatible with each other. Any incompatibility of such mixtures can also result in equipment failure if gelation or additive dropout occurs. 5.3x00a0;The test procedures described in this test method are designed to evaluate the performance of gear oils in each of the above circumstances. 5.4x00a0;This test method is based on the separate test methods FED-STD-791/3440.1 and FED-STD-791/3440.2. Minor changes have been made to the FED test methods to provide a coherent unified procedure. These changes do not significantly alter the test procedures. This test method has, therefore, potential for use as an alternative to the FED test methods in gear oil specifications such as SAE J2360 and Specification D5760. 1.1x00a0;This test method covers the determination of storage stability characteristics and the compatibility of automotive gear lubricants when blended with reference lubricants. The purpose of the test is to determine if performance-enhancing additives separate out under defined conditions. 1.2x00a0;The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.3x00a0;This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：75.100 (Lubricants, industrial oils and related pr CCS：E34 发布：2013 实施：

ASTM D5304-00 用氧超压评定馏出燃料贮存稳定性的标准试验方法
简介：
信息：ICS：75.080 CCS：发布：2000-06-10 实施：

GMW GMW15735-2011 粘合剂和密封材料的贮存稳定性.第2次出版(英文版本)[代替:GMNA GM9763P,GMNA GM9763P,GMNA GM9763P]
简介：
信息：ICS： CCS：发布：2011-08-01 实施：

ASTM F1105-95(1999)e1 贮存稳定性试验用液体型温度敏感型或溶剂型飞机清洗剂制备的标准试验方法
简介：
信息：ICS：49.040 CCS：发布：1999-05-10 实施：

ASTM D4144-94(2010) 紫外光固化涂料贮存稳定性的评定
简介：
信息：ICS：87.040 CCS：发布：2010-02-01 实施：

ASTM D4144-94(1999) 紫外光固化涂料贮存稳定性的评定
简介：
信息：ICS：87.040 CCS：发布：1999-05-10 实施：

ASTM D6930-2010 乳化沥青的沉降和贮存稳定性的标准试验方法
简介：This test method is useful for determining, in a comparatively short time, the storage stability or settlement of an emulsified asphalt. It is a measure of the permanence of the dispersion as related to time, but it is not to be construed to have significance as a measure of other stability aspects involved in use. 1.1 This test method covers the ability of an emulsified asphalt to remain as a uniform dispersion during storage. It is applicable to emulsified asphalts composed principally of a semisolid or liquid asphaltic base, water, and an emulsifying agent. 1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.3 This test method does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：93.080.20 CCS：E43 发布：2010 实施：

ASTM D3707-89(1999) 用烘箱试验法测定油包水乳液贮存稳定性的标准试验方法
简介：
信息：ICS：75.100 CCS：发布：1999-04-10 实施：

ASTM D4625-04(2009) 43℃和176℃下馏出燃料贮存稳定性的标准试验方法；C（110和176；（F）
简介：
信息：ICS：75.080 CCS：发布：2009-06-01 实施：

ASTM D4625-92(1998) 43摄氏度和176华氏度（110华氏度和176华氏度）下馏出燃料贮存稳定性的标准试验方法
简介：
信息：ICS：75.080 CCS：发布：1998-12-22 实施：