高温氧化检测标准

原创来源：北检院发布时间：2023-02-12 20:46:24 点击数：

全国服务领域：河北、山西、黑龙江、吉林、辽宁、江苏、浙江、安徽、福建、江西、山东、河南、湖北、湖南、广东、海南、四川、贵州、云南、陕西、甘肃、青海、台湾、内蒙古、广西、西藏、宁夏、新疆、北京、天津、上海、重庆、香港、澳门

高温氧化检测标准相关信息

GB/T 38804-2020 金属材料高温蒸汽氧化试验方法
简介：
信息：ICS：77.040.99 CCS：H21 发布：2020-06-02 00:00:00.0 实施：2021-01-01 00:00:00.0

ASTM D7359-2014a 采用高温氧化燃烧法和离子色谱检测法 (燃烧离子色谱-CIC) 的芳烃及其混合物中总氟, 氯和硫的标准试验方法
简介： 5.1x00a0;The total fluorine, chlorine and sulfur contained in aromatic hydrocarbon matrices can contribute to emissions, be harmful to many catalytic chemical processes, and lead to corrosion. This test method can be used to determine total sulfur and halogens in aromatic hydrocarbons and their mixtures. The results can be used for compliance determinations when acceptable to a regulatory authority using performance based criteria. 1.1x00a0;This test method covers the individual determination of total fluorine, chlorine and sulfur in aromatic hydrocarbons and their mixtures. Samples containing 0.10 to 10 mg/kg of each element can be analyzed. 1.2x00a0;This method can be applied to sample concentrations outside the range of the scope by dilution of the sample in an appropriate solvent to bring the total concentrations of fluorine, chlorine and sulfur within the range covered by the test method. However, it is the responsibility of the analyst to verify the solubility of the sample in the solvent and that the diluted sample results conform to the precision and accuracy of the method. 1.2.1x00a0;Special considerations must be made in order to attain detection limits below 1.0 mg/kg in a sample. The instrument must be clean and properly maintained to address potential sources of contamination, or carryover, or both. Multiple sequential injections shall be completed until a stable background is attained. A stable background is considered to be achieved when the analysis of a minimum of three consecutive system blanks have area counts equal to or less than 58201;% RSD for the anions of interest. 1.3x00a0;In determining the conformance of the test results using this method to applicable specifications, results shall be rounded off in accordance with the rounding-off method of Practice E29. 1.4x00a0;The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.5x00a0;This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. See Section 9.
信息：ICS：71.080.20 CCS：发布：2014 实施：

ASTM D6335-09 通过热氧化发动机油模拟试验测定高温沉积物的标准试验方法
简介：
信息：ICS：75.100 CCS：发布：2009-06-01 实施：

GB/T 38430-2019 金属和合金的腐蚀金属材料在高温腐蚀条件下的等温暴露氧化试验方法
简介：
信息：ICS：77.060 CCS：H25 发布：2019-12-31 00:00:00.0 实施：2020-07-01 00:00:00.0

SY/T 6954-2013 稠油高温氧化动力学参数测定方法热重法
简介：本标准规定了热重法测定稠油高温氧化动力学参数活化能、指前因子的方法。本标准适用于稠油高温氧化反应动力学参数的测定。
信息：ICS：75.0.20 CCS：E12 发布：2013-11-28 实施：2014-04-01

ASTM D7097-2009 用热氧化机油模拟试验测定适度高温活塞沉积物的试验方法.沉积物模拟实验
简介：The test method is designed to predict the deposit-forming tendencies of engine oil in the piston ring belt and upper piston crown area. Correlation has been shown between the TEOST MHT procedure and the TU3MH Peugeot engine test in deposit formation. Such deposits formed in the ring-belt area of a reciprocating engine piston can cause problems with engine operation and longevity. It is one of the required test methods in Specification D 4485 to define API Category-Identified engine oils. 1.1 This test method covers the procedure to determine the mass of deposit formed on a specially constructed test rod exposed to repetitive passage of 8.5 g of engine oil over the rod in a thin film under oxidative and catalytic conditions at 285x00B0;C. The range of applicability of the Moderately High Temperature Thermo-Oxidation Engine Test (TEOST MHT ) test method as derived from an interlaboratory study is approximately 10 to 100 mg. However, experience indicates that deposit values from 1 to 150 mg or greater may be obtained. 1.2 This test method uses a patented instrument, method and patented, numbered, and registered depositor rods traceable to the manufacturer and made specifically for the practice and precision of the test method. 1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.3.1 The values stated in SI units are to be regarded as standard. Although not an SI unit, the special name, litre (L) is allowed by SI for the cubic decimetre (dm3) and the millilitre (mL) for the SI cubic centimetre (cm3). 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：75.100 (Lubricants, industrial oils and related pr CCS：E34 发布：2009 实施：

GB/T 38231-2019 金属和合金的腐蚀金属材料在高温腐蚀条件下的热循环暴露氧化试验方法
简介：
信息：ICS：77.060 CCS：H25 发布：2019-10-18 00:00:00.0 实施：2020-05-01 00:00:00.0

ASTM D4129-05(2013) 高温氧化法和库仑法检测水中总有机碳的标准试验方法
简介：
信息：ICS：13.060.50 CCS：发布：2013-05-01 实施：

ASTM D6335-2009 通过热氧化发动机油模拟试验测定高温沉积物的标准试验方法
简介：The test method is designed to predict the high temperature deposit forming tendencies of an engine oil. This test method can be used to screen oil samples or as a quality assurance tool.1.1 This test method covers the procedure to determine the amount of deposits formed by automotive engine oils utilizing the thermo-oxidation engine oil simulation test (TEOST ). An interlaboratory study (see Section 17) has determined it to be applicable over the range from 10 to 65 mg total deposits. Note 18212;Operational experience with the test method has shown the test method to be applicable to engine oils having deposits over the range from 2 to 180 mg total deposits. 1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.2.1 Milligrams (mg), grams (g), millilitres (mL), and litres are the units provided, because they are an industry accepted standard. 1.2.2 Exception8212;Provided psig for information only in 6.2. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：75.100 (Lubricants, industrial oils and related pr CCS：E34 发布：2009 实施：

GB/T 29037-2012 热喷涂抗高温腐蚀和氧化的保护涂层
简介：本标准适用于温度1 000℃(1 273 K)以下作为抗腐蚀保护的金属热喷涂涂层、保护钢铁耐大气腐蚀的热喷涂铝或锌涂层参照GB/T 9793、本标准不包括喷涂工艺制备的非金属材料涂层、
信息：ICS：25.220.20 CCS：A29 发布：2012-12-31 实施：2013-10-01

ASTM D7359-2013 采用高温氧化燃烧法和离子色谱检测法(燃烧离子色谱-CIC)测定芳烃及其混合物中总氟, 氯和硫的标准试验方法
简介： 4.1x00a0;The total fluorine, chlorine and sulfur contained in aromatic hydrocarbon matrices can contribute to emissions, be harmful to many catalytic chemical processes, and lead to corrosion. This test method can be used to determine total sulfur and halogens aromatic hydrocarbon matrices, in finished products and can be used for compliance determinations when acceptable to a regulatory authority using performance based criteria. 1.1x00a0;This test method covers the individual determination of total fluorine, chlorine and sulfur in aromatic hydrocarbons and their mixtures. Samples containing 0.10 to 50 mg/kg of each element can be analyzed. 1.2x00a0;This method can be applied to sample types outside the range of the scope by dilution of the sample in an appropriate solvent to bring the total concentrations of fluorine, chlorine and sulfur within the range covered by the test method. However, it is the responsibility of the analyst to verify the solubility of the sample in the solvent and that the diluted sample results conform to the precision and accuracy of the method. 1.3x00a0;In determining the conformance of the test results using this method to applicable specifications, results shall be rounded off in accordance with the rounding-off method of Practice E29. 1.4x00a0;The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.5x00a0;This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. See Section 8.
信息：ICS：71.080.20 (Halogenated hydrocarbons) CCS：发布：2013 实施：

ASTM D6514-03(2008) 汽轮机油高温通用氧化试验的标准试验方法
简介：
信息：ICS： CCS：发布：2008-12-01 实施：

GB/T 2951.42-2008 电缆和光缆绝缘和护套材料通用试验方法.第42部分:聚乙烯和聚丙烯混合料专用试验方法.高温处理后抗张强度和断裂伸长率试验.高温处理后卷绕试验.空气热老化后的卷绕试验.测定质量的增加.长期热稳定性试验.铜催化氧化降解试验方法
简介：GB/T 2951的本部分规定了配电及通信用电缆和光缆，包括船舶与近海用电缆和光缆的聚合物绝缘和护套材料的试验方法。这些试验方法适用于聚烯烃绝缘和护套。
信息：ICS：29.060 CCS：K15;K13 发布：2008-06-26 实施：2009-04-01

DL/T 1162-2012 火电厂金属材料高温蒸汽氧化试验方法
简介：本标准规定了火力发电厂金属材料高温蒸汽氧化试验的基本要求。本标准适用于火力发电厂蒸汽流通部件的金属材料高温蒸汽氧化试验。
信息：ICS：27.100 CCS：H25 发布：2012-08-23 实施：2012-12-01

SAE AMS 5940C-2008 34Co 3.0Cr 28Ni 3.0Cb(Nb) 5.5Al 0.008B 25.5Fe多重熔炼,高温,耐氧化,低膨胀溶解热处理,沉淀可硬化的耐腐蚀和耐热合金棒材,锻件和环材
简介：1.1 FormThis specification covers a cobalt-nickel-iron alloy in the form of bars, forgings, flash welded rings, and stock for forging,flash welded rings, or heading.1.2 ApplicationThese products have been used typically for parts requiring a combination of high strength and low expansion propertiesup to 1300 °F (704 °C), but usage is not limited to such applications.
信息：ICS：49.025.10 CCS：V11 发布：2008-07-15 实施：

ASTM D4129-05(2020) 高温氧化法和库仑法检测水中总有机碳的标准试验方法
简介：
信息：ICS：13.060.50 CCS：发布：2020-01-01 实施：

NF A05-120-2012 金属与合金的腐蚀. 金属材料在高温腐蚀条件下等温暴露氧化试验方法.
简介：
信息：ICS：77.060 CCS：A29 发布：2012-05-01 实施：2012-05-04

EJ/T 1212.9-2008 烧结氧化钆-二氧化铀芯块分析方法.第9部分:高温水解离子选择性电极法测定氟
简介：本部分规定了烧结氧化钆-二氧化铀(GdO-UO)芯块中氟元素测定的方法提要、试剂、仪器设备、试样、分析步骤、结果计算及方法精密度。本部分适用于GdO-UO芯块中氟含量的测定。也适用于含钆二氧化铀粉末氟含量的测定。取样量为（0.5～2）g时，测定氮的质量分数范围为（2.5～100）μg/g。
信息：ICS：27.120.30 CCS：F46 发布：2008-03-17 实施：2008-10-01

ASTM D7097-19 用热氧化发动机机油模拟试验测定中高温活塞沉积物的标准试验方法&x2014；TEOST MHT
简介：
信息：ICS：75.100 CCS：发布：2019-12-01 实施：

BS ISO 21608-2012 金属和合金的腐蚀.金属材料高温腐蚀条件下等温接触氧化测试用检测方法
简介：
信息：ICS：77.060 CCS：H25 发布：2012-04-30 实施：2012-04-30

EJ/T 1212.6-2008 烧结氧化钆-二氧化铀芯块分析方法.第6部分:高温水解离子选择性电极法测定氯
简介：本部分规定了烧结氧化钆-二氧化铀(GdO-UO)芯块中氯元素测定的方法提要、试剂、仪器设备、试样制备、分析步骤、结果计算及方法精密度。本部分适用于烧结GdO-UO芯块中氯含量的测定。取样量为（0.5～5.0）g时，测定氯元素的质量分数范围为（2～200）μg/g。
信息：ICS：27.120.30 CCS：F46 发布：2008-03-17 实施：2008-10-01

ASTM D6335-19 通过热氧化发动机油模拟试验测定高温沉积物的标准试验方法
简介：
信息：ICS：75.100 CCS：发布：2019-12-01 实施：

ASTM D7359-2008 用高温氧化燃烧法和离子色谱检测法(燃烧离子色谱-CIC)测定芳烃及其混合物中总氟、氯和硫磺的标准试验方法
简介：The total fluorine, chlorine and sulfur contained in aromatic hydrocarbon matrices can contribute to emissions, be harmful to many catalytic chemical processes, and lead to corrosion. This test method can be used to determine total sulfur and halogens aromatic hydrocarbon matrices, in finished products and can be used for compliance determinations when acceptable to a regulatory authority using performance based criteria.1.1 This test method covers the individual determination of total fluorine, chlorine and sulfur in aromatic hydrocarbons and their mixtures. Samples containing 0.1 to 50 mg/kg of each element can be analyzed. 1.2 This method can be applied to sample types outside the range of the scope by dilution of the sample in an appropriate solvent to bring the total concentrations of fluorine, chlorine and sulfur within the range covered by the test method. However, it is the responsibility of the analyst to verify the solubility of the sample in the solvent and that the diluted sample results conform to the precision and accuracy of the method. 1.3 In determining the conformance of the test results using this method to applicable specifications, results shall be rounded off in accordance with the rounding-off method of Practice E 29. 1.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. See Section 8.
信息：ICS：71.080.20 (Halogenated hydrocarbons) CCS：G17 发布：2008 实施：

ASTM D6514-03(2019) 汽轮机油高温通用氧化试验的标准试验方法
简介：
信息：ICS：27.060.10 CCS：发布：2019-05-01 实施：

ISO 21608:2012 金属和合金的腐蚀——金属材料在高温腐蚀条件下等温暴露氧化试验的试验方法
简介：
信息：ICS：77.060 CCS：发布：2012-03-12 实施：

SAE AMS 5940B-2007 沉积可硬化、低膨胀溶解热处理、耐氧化、高温、多重熔融的耐腐蚀耐热34Co 3.0Cr 28Ni 3.0Cb(Nb) 5.5Al 0.008B 25.5Fe合金棒材、锻件和环材
简介：This specification covers a cobalt-nickel-iron alloy in the form of bars, forging,s flash welded rings, and stock for forging, flash welded rings, or heading. These products have been used typically for parts requiring a combination of high strength and low expansion properties up to 1300 °F (704 °C), but usage is not limited to such applications.
信息：ICS：49.025.10 CCS：V11 发布：2007-05-01 实施：

ASTM D6514-03(2019)e1 汽轮机油高温通用氧化试验的标准试验方法
简介：
信息：ICS：27.060.10 CCS：发布：2019-05-01 实施：

ISO 21608-2012 金属和合金的腐蚀.金属材料高温腐蚀条件下等温接触氧化测试用检测方法
简介：
信息：ICS：77.060 CCS：H25 发布：2012-03 实施：

ASTM D7097-06a 用热氧化发动机油模拟试验方法测定中高温活塞沉积物的标准试验方法
简介：
信息：ICS：75.100 CCS：发布：2006-12-01 实施：

BS EN ISO 6581-2018 铝和铝合金阳极氧化. 有色阳极氧化涂层对紫外线和高温的比较牢固度测定
简介：
信息：ICS：25.220.20;77.120.10 CCS：A29 发布：2018-10-08 实施：2018-10-08

ASTM D4129-05(2012) 高温氧化法和库仑法检测水中总有机碳的标准试验方法
简介：
信息：ICS：13.060.50 CCS：发布：2012-01-01 实施：

ASTM D7097-06 用热氧化发动机油模拟试验方法测定中高温活塞沉积物的标准试验方法
简介：
信息：ICS：75.100 CCS：发布：2006-05-15 实施：

ISO 20236:2018 水质.高温催化氧化燃烧后总有机碳（TOC）、溶解有机碳（DOC）、总结合态氮（TNB）和溶解结合态氮（DNB）的测定
简介：
信息：ICS：13.060.50 CCS：发布：2018-10-02 实施：

JIS C3660-4-2-2011 电缆绝缘和护套材料.通用试验方法.第4-2部分:聚乙烯和聚丙烯化合物用专门方法.温度升高时调节后抗张强度和断裂延伸率.高温时调节后缠绕试验.空气热时效后缠绕试验.质量增加测定.长期稳定性试验.铜催化氧化降解试验方法
简介：
信息：ICS：29.035.20;29.060.20 CCS：K15 发布：2011-01-20 实施：

SH/T 0788-2006 内燃机油高温氧化和轴瓦腐蚀评定法(程序Ⅷ法)
简介： 1.1 本标准规定了评定内燃机油的高温氧化和轴瓦腐蚀性能的方法。试验规定使用CLR油料试验机，用无铅汽油作燃料，评价内燃机油的高温氧化和轴瓦腐蚀性能（粘度级别包括5W、1OW、20、30、40、50和多级油）以及多级油的粘度变化。 1.2 试验结果与汽车发动机使用结果之间的相关性未建立。因此，本试验所得结果不能充分显示所有点火式或压燃式发动机在不同于该试验方法的结果，但该油品试验具有很好的区分性。 1.3 只用[SI]单位作为标准单位。 1.4 本标准涉及某些有危险性的材料、操作和设备，但没有对与此有关的所有安全问题都提出建议，因此，用户在使用本标准前应建立适当的安全制度和防护措施。
信息：ICS：75.100 CCS：E34 发布：2006-05-12 实施：2006-11-01

ASTM D6335-18 通过热氧化发动机油模拟试验测定高温沉积物的标准试验方法
简介：
信息：ICS：75.100 CCS：发布：2018-06-01 实施：

KS D ISO 17834-2010 热喷涂.高温下抗腐蚀耐氧化保护涂层
简介：이 표준은 1 000 ℃(1 273 K) 이하 온도에서 부식 방지를 위해 용사된 금속 피복
信息：ICS：25.220.20 CCS：A29 发布：2010-12-29 实施：2010-12-29

ASTM D7097-2006a 用热氧化机油模拟试验测定中等高温活塞沉积物的标准试验方法.TEOST MHT
简介：The test method is designed to predict the deposit-forming tendencies of engine oil in the piston ring belt and upper piston crown area. Correlation has been shown between the TEOST MHT procedure and the TU3MH Peugeot engine test in deposit formation. Such deposits formed in the ring-belt area of a reciprocating engine piston can cause problems with engine operation and longevity. It is one of the required test methods in Specification D 4485 to define API Category-Identified engine oils.6 1.1 This test method covers the procedure to determine the mass of deposit formed on a specially constructed test rod exposed to repetitive passage of 8.5 g of engine oil over the rod in a thin film under oxidative and catalytic conditions at 285C. The range of applicability of the Moderately High Temperature Thermo-Oxidation Engine Test (TEOST MHT) test method as derived from an interlaboratory study is approximately 10 to 100 mg. However, experience indicates that deposit values from 1 to 150 mg or greater may be obtained.1.2 This test method uses a patented instrument, method and patented, numbered, and registered depositor rods traceable to the manufacturer and made specifically for the practice and precision of the test method.Note 1ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentioned in this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the risk of infringement of such rights, are entirely their own responsibility.1.3 The values stated in SI units are to be regarded as standard. Although not an SI unit, the special name, litre (L) is allowed by SI for the cubic decimetre (dm3) and the millilitre (mL) for the SI cubic centimetre (cm3).1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：75.100 (Lubricants, industrial oils and related pr CCS：E34 发布：2006 实施：

ASTM D6335-16 通过热氧化发动机油模拟试验测定高温沉积物的标准试验方法
简介：
信息：ICS：75.100 CCS：发布：2016-10-01 实施：

ASTM D7097-2006 用热氧化机油模拟试验测定中等高温活塞沉积物的标准试验方法.TEOST MHT
简介：1.1 This test method covers the procedure to determine the mass of deposit formed on a specially constructed test rod exposed to repetitive passage of 8.5 g of engine oil over the rod in a thin film under oxidative and catalytic conditions at 285176;C. The range of applicability of the Moderately High Temperature Thermo-Oxidation Engine Test (TEOST MHT) test method as derived from an interlaboratory study is approximately 10 to 100 mg. However, experience indicates that deposit values from 1 to 150 mg or greater may be obtained.1.2 This test method uses a patented instrument, method and patented, numbered, and registered depositor rods traceable to the manufacturer and made specifically for the practice and precision of the test method.Note 1ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentioned in this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the risk of infringement of such rights, are entirely their own responsibility.1.3 The values stated in SI units are to be regarded as standard. Although not an SI unit, the special name, litre (L) is allowed by SI for the cubic decimetre (dm3) and the millilitre (mL) for the SI cubic centimetre (cm3).This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
信息：ICS：75.100 (Lubricants, industrial oils and related pr CCS：E34 发布：2006 实施：

ASTM D7097-16a 用热氧化发动机机油模拟试验测定中高温活塞沉积物的标准试验方法&x2014；TEOST MHT
简介：
信息：ICS：75.100 CCS：发布：2016-09-01 实施：

ASTM C863-00(2010) 评估碳化硅耐火材料在高温下的耐氧化性的标准试验方法
简介：
信息：ICS：81.080 CCS：发布：2010-11-01 实施：

ASTM C863-00(2005) 评估碳化硅耐火材料在高温下的耐氧化性的标准试验方法
简介：
信息：ICS： CCS：发布：2005-12-01 实施：

ASTM D7097-16 用热氧化发动机机油模拟试验测定中高温活塞沉积物的标准试验方法&x2014；TEOST MHT
简介：
信息：ICS：75.100 CCS：发布：2016-07-01 实施：

BS EN ISO 6581-2010 铝和铝合金阳极氧化.有色阳极氧化涂层对紫外线和高温的比较牢固度测定
简介：This International Standard specifies a comparative method for the determination of the fastness of colouredanodic oxidation coatings to ultraviolet (UV) light and heat.The method is not suitable for testing coloured anodic oxidation coatings that are heat sensitive.NOTE Dark-coloured test pieces will normally reach the highest temperatures.
信息：ICS：25.220.20;77.120.10 CCS：A29 发布：2010-08-31 实施：2010-08-31

SH/T 0783-2005 内燃机油高温氧化和抗磨损性能评定法(CEPT-III法）
简介： 本标准规定了评定内燃机油的高温氧化变稠、高温油泥和漆膜等沉积物生成倾向及抗磨损性能的方法。本标准适用于汽油机油（如：SE、SF）的性能评定和相关的柴油机油性能评定。
信息：ICS：75.100 CCS：E34 发布：2005-11-28 实施：2006-06-01

ASTM D6514-03(2014) 汽轮机油高温通用氧化试验的标准试验方法
简介：
信息：ICS：27.060.10 CCS：发布：2014-10-01 实施：

NB/SH/T 0834-2010 发动机油适度高温活塞沉积物的测定　热氧化模拟试验法（TEOST MHT）
简介：1-1本标准规定了在285℃的氧化和催化条件下，用8.5g发动机油以薄层油膜的形式反复通过一根特殊结构的试验棒，然后测定棒上生成沉积物的方法。实验室间的研究发现，适度高温热氧化发动机模拟试验(TEOST MHT)的适用范围为lOmg～100mg，但经验表明，当沉积物质量在1mg～150mg或更大值时也可适用。1-2本标准采用了具有专利权的仪器、方法以及获得专利、编号并注册的沉积棒，通过编号可以追溯到生产商，这种沉积棒是针对本试验方法的用途和精度专门制作的。1．3本标准采用国际单位制[SI]单位。1-4本标准的使用可能涉及到某些有危险性的材料、操作和设备，但无意对与其使用相关的所有安全问题都提出建议。因此，用户在使用本标准之前应建立适当的安全和防护措施，并确定相关规章限制的话用件。
信息：ICS：75.100 CCS：E34 发布：2010-05-01 实施：2010-10-01

KS C IEC 60811-4-2-2005(2016) 电缆和光缆绝缘和护套材料通用试验方法第4－2部分:聚乙烯和聚丙烯化合物专用试验方法高温处理后的拉伸强度和断裂伸长率高温处理后的缠绕试验热老化后的缠绕试验空气－质量增加的测量－长期稳定性试验－铜催化氧化降解试验方法
简介：
信息：ICS：29.060.20 CCS：发布：2005-09-30 实施：

SAE AMS 5940D-2014 34Co-3.0Cr-28Ni-3.0Cb(Nb)-5.5Al-0.008B-25.5Fe多重熔炼,高温,耐氧化,低膨胀溶解热处理,沉淀可硬化的耐腐蚀和耐热合金棒材,锻件和环材
简介：This specification covers a cobalt-nickel-iron alloy in the form of bars, forgings, flash welded rings, and stock for forging, flash welded rings, or heading.
信息：ICS：49.025.10 CCS：V11 发布：2014-05-05 实施：

KS D 0296-2009 不锈钢板材高温氧化涂层的面积电阻测量试验方法
简介：이 시험방법은 스테인리스강 판재의 고온 산화에 의해 생성된 산화 피막의 고온 면비저항 (A
信息：ICS：77.060 CCS：H59 发布：2009-12-29 实施：2009-12-29

KS C IEC 60811-4-2-2005 电缆和光缆的绝缘和护套材料的通用试验方法.第4-2部分:聚乙烯和聚丙烯化合物专用方法.高温处理后抗拉强度和断裂伸长度.高温处理后的卷绕试验.在空气中热老化后的卷绕试验.质量增加的测量.长期稳定性试验.催化铜氧化降解的试验方法
简介：이 규격은 선박 및 근해 설비용 케이블을 포함한 전력 분배 및 전기 통신용 전기 및 광섬유
信息：ICS：29.060.20 CCS：K13;M33 发布：2005-09-30 实施：2005-09-30

DB15/T 688.3-2014 二氧化钍粉末化学分析方法第3部分：二氧化钍粉末中氟的测定—高温水解离子选择性电极法
简介：
信息：ICS：71.060.20 CCS：G 13 发布：2014-04-01 实施：2014-06-01

KS D 0296-2009 不锈钢板材高温氧化涂层的面积电阻测量试验方法
简介：이 시험방법은 스테인리스강 판재의 고온 산화에 의해 생성된 산화 피막의 고온 면비저항 (A
信息：ICS：77.06 CCS：H59 发布：2009-12-29 实施：2009-12-29

ASTM D7359-2014 用高温氧化燃烧法和离子色谱检测法 (燃烧离子色谱法-CIC) 测定芳烃和其混合物中总氟, 氯和硫磺的标准试验方法
简介： 5.1x00a0;The total fluorine, chlorine and sulfur contained in aromatic hydrocarbon matrices can contribute to emissions, be harmful to many catalytic chemical processes, and lead to corrosion. This test method can be used to determine total sulfur and halogens in aromatic hydrocarbons and their mixtures. The results can be used for compliance determinations when acceptable to a regulatory authority using performance based criteria. 1.1x00a0;This test method covers the individual determination of total fluorine, chlorine and sulfur in aromatic hydrocarbons and their mixtures. Samples containing 0.10 to 10 mg/kg of each element can be analyzed. 1.2x00a0;This method can be applied to sample concentrations outside the range of the scope by dilution of the sample in an appropriate solvent to bring the total concentrations of fluorine, chlorine and sulfur within the range covered by the test method. However, it is the responsibility of the analyst to verify the solubility of the sample in the solvent and that the diluted sample results conform to the precision and accuracy of the method. 1.2.1x00a0;Special considerations must be made in order to attain detection limits below 1.0 mg/kg in a sample. The instrument must be clean and properly maintained to address potential sources of contamination, or carryover, or both. Multiple sequential injections shall be completed until a stable background is attained. A stable background is considered to be achieved when the analysis of a minimum of three consecutive system blanks have area counts equal to or less than 5 % RSD for the anions of interest. 1.3x00a0;In determining the conformance of the test results using this method to applicable specifications, results shall be rounded off in accordance with the rounding-off method of Practice E29. 1.4x00a0;The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.5x00a0;This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. See Section 9.
信息：ICS：71.080.20 (Halogenated hydrocarbons) CCS：发布：2014 实施：

ASTM D6335-09 通过热氧化发动机油模拟试验测定高温沉积物的标准试验方法
简介：
信息：ICS：75.100 CCS：发布：2009-06-01 实施：

KS C IEC 60811-4-2-2005(2021) 电缆和光缆的绝缘和护套材料通用试验方法第4－2部分:聚乙烯和聚丙烯化合物专用方法高温处理后的拉伸强度和断裂伸长率高温处理后的缠绕试验热老化后的缠绕试验空气－质量增加测量－长期稳定性试验－铜催化氧化降解试验方法
简介：
信息：ICS：29.060.20 CCS：发布：2005-09-30 实施：